logo
Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
News
TOGETHER HTL LTD
Home News

Cooling Roll Diameter for Cast Film Lines: The Complete Engineering Guide

TOGETHER HTL LTD is a very good company , I am very willing to cooperate with you, safe, efficient, professional, honest, happy! Thank you for providing me with stable service and products. -----EUROPAT

—— EUROPT INDUSTRIAL

I'm Online Chat Now
Company News
Cooling Roll Diameter for Cast Film Lines: The Complete Engineering Guide
Latest company news about Cooling Roll Diameter for Cast Film Lines: The Complete Engineering Guide

Cooling Roll Diameter for Cast Film Lines: The Complete Engineering Guide

Quick Answer

What is the right cooling roll diameter? It is the diameter that removes your heat load inside the contact time your casting speed allows, without exceeding about 25–60 kW/m² of wetted surface, while holding runout, balance and deflection inside the limits your product grade demands. That is four constraints, not one, and the diameter is simply the value that satisfies all four.

Key Takeaways

· Diameter sets contact length; the internal circuit sets the heat transfer coefficient.

· Heat load is fixed by the product, so the roll can only change area and residence time.

· Below roughly 150–200 µm sheet thickness, the coolant side is the controlling resistance.

· Contact time under 0.35 s at full casting speed is a design warning, not a preference.

· Runout, balance and deflection behave like thermal variables above 250 m/min.

Summary Table

Item

Description

Function

Quench the extruded web and set surface quality before orientation

Typical diameter

400–2,000 mm; up to 3,500 mm for special wide drums

Construction

Double-shell steel shell, spiral baffles, chrome or matte face

Working flux

25–60 kW/m² of wetted area

Uniformity

±0.5 to ±1 °C across the face under load

Service life

10+ years with treated water and one re-grind

 

Definition: What a Cast Film Cooling Roll Actually Is

A cooling roll is a rotating heat exchanger. Molten polymer leaves a slit die, crosses a short air gap, and is pressed against a temperature-controlled cylinder by an air knife, a pinning wire or an electrostatic system. Heat leaves the web through the polymer, across the interface, through the shell and into a circulating coolant, usually treated water between 15 and 60 °C depending on the product.

The mechanical description is equally important: it is a pressure vessel that rotates at speed, carries a chrome or ceramic face measured in microns of flatness, and transmits torque through journals that must stay aligned to a few thousandths of a millimetre. Both descriptions are true at once, and the diameter decision has to satisfy both.

Where the Roll Sits in the Line

Previous process: extruder, melt filter, die head, air gap, pinning device.

Current process: casting roll or chill roll, coolant circuit, temperature control unit.

Next process: **MDO preheating rolls**, **MDO stretching rolls**, TD orientation, then **film converting rolls** downstream if the product is coated or laminated.

The line-wide view matters because output on a cast line is often cooling-limited. When the casting section is the constraint, every other upgrade — a bigger extruder, a faster winder — transfers capital to a bottleneck that has not moved. The roll families for this section are grouped under **casting film rolls** and the oriented-film families under **bi-oriented film rolls**.

The Heat Transfer Chain

Four resistances act in series, and only the largest one governs the achievable flux:

1. Polymer conduction. Proportional to thickness squared over thermal diffusivity. Negligible for 20 µm film; dominant for 1 mm sheet.

2. Interface resistance. Depends on contact pressure, surface finish and whether the polymer is above or below its glass transition during contact.

3. Shell conduction. Steel is several hundred times more conductive than polymer, so the shell is rarely limiting — unless the wall is very thick or the flux is very high.

4. Coolant boundary layer. Governed by velocity and channel geometry. This is where most undersized rolls actually fail.

The engineering conclusion is uncomfortable for buyers who want a simple answer: the diameter matters most where the polymer is thick, and matters least where the polymer is thin. A 25 µm BOPET line at 400 m/min does not need a 1,500 mm drum because the polymer needs time; it needs it because the drum has to present enough area and enough coolant velocity to absorb a very large heat flow in a very short contact.

The Three-Number Method

Number one: heat load

Q = ṁ × (cp × ΔT + ΔHf)

Polyolefins need about 700–930 kJ/kg from melt to solid web. PP from 240 °C to 30 °C sits near 650–750 kJ/kg once crystallisation heat is counted. PET from 290 °C to 75 °C sits near 350–420 kJ/kg, but the quench must be completed within a fraction of a second.

Number two: contact time

L = π × D × (θ / 360) and t = L / v, where v is the web speed at the roll. In a sequential line this is the casting speed, not the post-MDO speed. Using finished-film speed in the calculation is the single most common error in roll enquiries, and it always produces an undersized roll.

Number three: heat flux

q = Q / (L × W), where W is the net casting width. Cast film rolls normally work between 25 and 60 kW/m². Above that band, surface temperature rises faster than the coolant can absorb the load.

Three Worked Examples

CPP line. 650 kg/h, 2.0 m net width, 50 µm, 120 m/min, 200° wrap, 800 kJ/kg → 144 kW.

Diameter

Contact length

Contact time

Wetted area

Heat flux

600 mm

1.05 m

0.52 s

2.09 m²

69 kW/m²

700 mm

1.22 m

0.61 s

2.44 m²

59 kW/m²

900 mm

1.57 m

0.79 s

3.14 m²

46 kW/m²

 

BOPP tenter line. 1,600 kg/h, 4.2 m net width, 180 m/min, 210° wrap, 750 kJ/kg → 333 kW.

Diameter

Contact length

Contact time

Wetted area

Heat flux

800 mm

1.47 m

0.49 s

6.16 m²

54 kW/m²

1,000 mm

1.83 m

0.61 s

7.70 m²

43 kW/m²

1,200 mm

2.20 m

0.73 s

9.24 m²

36 kW/m²

 

BOPET thin film. 1,200 kg/h, 2.6 m net width, 12 µm, 300 m/min, 220° wrap, 400 kJ/kg → 133 kW.

Diameter

Contact length

Contact time

Wetted area

Heat flux

800 mm

1.54 m

0.31 s

3.99 m²

33 kW/m²

1,000 mm

1.92 m

0.38 s

4.99 m²

27 kW/m²

1,200 mm

2.30 m

0.46 s

5.99 m²

22 kW/m²

 

Read across the three tables and the pattern is clear. The CPP line is thermally comfortable at 900 mm. The BOPP line needs 1,200 mm because the face is wide and the flux at 800 mm is marginal. The BOPET line is not flux-limited at all — it is time-limited, which is why thin-film drums are chosen for contact time and uniformity rather than for heat flux.

Diameter Versus Line Speed

Casting speed

Pub Time : 2026-11-17 18:02:55 >> News list
Contact Details
TOGETHER HTL LTD

Contact Person: Mr. Maple

Tel: +86 17778255675

Fax: 86--311-80690567

Send your inquiry directly to us (0 / 3000)