logo
Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
News
TOGETHER HTL LTD
Home News

How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?

TOGETHER HTL LTD is a very good company , I am very willing to cooperate with you, safe, efficient, professional, honest, happy! Thank you for providing me with stable service and products. -----EUROPAT

—— EUROPT INDUSTRIAL

I'm Online Chat Now
Company News
How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?
Latest company news about How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?

How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?

Summary Table

Item

Description

Function

Suspends above the conveyor and continuously lifts ferrous tramp metal out of the burden onto a self-cleaning discharge belt

Working gap rule

0.2–0.3 × belt width; burden depth + 50–100 mm safety clearance; typical range 150–450 mm

Field type

Permanent (shallow–medium burden) vs electromagnetic (deep burden, fast belts, heavy pieces)

Belt speed limit

Best capture at 1.5–2.5 m/s; above 3.0 m/s a deep-penetration electromagnet is required

Width rule

Magnet face 200–400 mm wider than the conveyor belt

Service life

Magnetic circuit 10+ years; discharge belt, rollers and chute liners are the wearing items

Benefits

Protects crushers and screens, cuts liner replacement, reduces unplanned downtime

latest company news about How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?  0FAQ

Q1: What is the correct suspension height for a self-cleaning overband magnet?

A: Start at 0.2–0.3 × belt width — 200–300 mm for a 1,000 mm conveyor — then correct for burden depth: maximum material layer thickness plus 50–100 mm of safety clearance, measured from the magnet working face to the deepest position a target steel piece can occupy. Use the larger of the two values, and never go below the clearance needed for the largest lump to pass safely.

Q2: Why does a small height error matter so much?

A: Magnetic pull decays steeply with distance — approximately with the cube of distance near the face. Doubling the gap can leave a steel piece with less than a third of the force needed to lift it, and fine contaminants are the first to pass through uncaptured.

Q3: Should the height be measured to the belt surface or to the steel?

A: To the steel. The height that governs capture is the distance from the magnetic pole working surface to the deepest position the target object can occupy — normally the bottom of the burden layer against the belt. Measuring to the bare belt understates the true working distance by the full burden depth.

Q4: What happens if I mount the magnet too close to the belt?

A: Oversized lumps can strike the magnet face or the self-cleaning discharge belt, causing tears, tracking failure and unplanned separator downtime. Safe clearance for the largest possible lump is a hard floor; capture optimisation happens above it.latest company news about How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?  1

Conclusion

The question "how close should the magnet be?" has a disciplined answer, not a guess: start at 0.2–0.3 × belt width, add burden-depth correction with a 50–100 mm clearance floor, measure from the working face to the deepest position the steel can occupy, and let belt speed decide whether a permanent or electromagnetic circuit is physically capable of the lift. Set the hard collision floor first, optimise capture above it, keep the magnet face wider than the belt, and guard the setting with a monthly gap log — because height drift, not magnet failure, is what quietly leaks tramp iron into your crushers. Get the gap right and every downstream wear part, from liners to Conveyor Belts, lasts exactly as long as its engineering says it should.

HUATAO Group supplies mining wear parts and separation equipment — self-cleaning and electromagnetic overband separators, magnetic drums and rollers, screen panels, crusher wear parts and conveyor protection components — with OEM manufacturing to drawing and export experience across mining projects worldwide.

Contact Us

Contact: Annie Lu

Email: annie.lu@huataogroup.com

Phone / WhatsApp: +86 180 3242 2676

Website: http://www.tufflexscreen.com

We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.

Pub Time : 2026-11-20 16:43:46 >> News list
Contact Details
TOGETHER HTL LTD

Contact Person: Mr. Maple

Tel: +86 17778255675

Fax: 86--311-80690567

Send your inquiry directly to us (0 / 3000)