logo
Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
News
TOGETHER HTL LTD
Home News

Self-Cleaning Iron Remover on a Mobile Crushing Plant: Diesel Generator Power or Hydraulic Drive?

TOGETHER HTL LTD is a very good company , I am very willing to cooperate with you, safe, efficient, professional, honest, happy! Thank you for providing me with stable service and products. -----EUROPAT

—— EUROPT INDUSTRIAL

I'm Online Chat Now
Company News
Self-Cleaning Iron Remover on a Mobile Crushing Plant: Diesel Generator Power or Hydraulic Drive?
Latest company news about Self-Cleaning Iron Remover on a Mobile Crushing Plant: Diesel Generator Power or Hydraulic Drive?

Self-Cleaning Iron Remover on a Mobile Crushing Plant: Diesel Generator Power or Hydraulic Drive?

Summary Table

Decision Factor

Diesel Generator (Electric)

Hydraulic Drive

Permanent Magnet + Genset Belt

Added continuous load

3–9 kW coil + 0.75–2.2 kW belt (electromagnetic)

15–25 L/min @ 150–200 bar from host pump

0.75–2.2 kW belt only

Extra fuel burn

+1.5–2.0 L/h (EM) / +0.2–0.4 L/h (PM)

~+0.3–0.6 L/h via engine load

+0.2–0.4 L/h

Belt-speed stability

Excellent (±2%)

Fair (±10% with oil temp)

Excellent (±2%)

Cold start below –20 °C

Hard without cold-start kit

Good with arctic oil

Good (belt only)

Installed cost on hydraulic-only plant

High (genset must be added)

Low (reuses pump circuit)

Medium

Best fit

Quarries, mining campaigns

Rental demolition, recycling

Plants that already run a genset

Market Watch (November 19–20, 2026)

· Gold broke down hard: spot gold slid 2.67% to ~$3,625/oz and COMEX futures fell 3.05% to $3,627.90/oz — the sharpest single-week drawdown in over a year, pressured by a hawkish Fed minutes release and a seasonally strong dollar index near 103.9.

· Silver fell even harder: COMEX silver dropped 4.94% to $42.84/oz, widening the gold-silver ratio back above 84.

· Copper slipped again: LME three-month copper closed at $12,453/t (-1.37% on the day), extending last week's retreat from the $13,000+ zone as funds de-risked into year-end.

· Base metals mixed: LME zinc gained 1.88% to $3,549.5/t and aluminum rose 1.63% to $2,868.5/t, while nickel (-1.10% to $15,680/t) and tin (-1.86% to $41,995/t) followed copper lower.

· Diesel-relevant signal: Brent crude firmed 0.79% to $92.68/bbl and WTI held near $83.2/bbl — fuel costs for diesel-generator-powered mobile fleets remain near cycle highs, which strengthens the case for permanent-magnet (low-draw) magnet configurations on genset-fed plants.

· Iron ore bounced: iron ore futures closed up more than 2% in the night session, and rebar output held near 1.83 Mt/week — aggregate and ore contractors continue to run full mobile fleets through the quarter.

The fuel-price backdrop matters directly for this topic: every 0.5 L/h of avoidable burn on a mobile plant is roughly $1.4–1.8/h at current Brent-linked diesel prices — about $35–45 per 24-hour campaign day.latest company news about Self-Cleaning Iron Remover on a Mobile Crushing Plant: Diesel Generator Power or Hydraulic Drive?  0

Case Study

A contract crushing operator running a track-mounted impactor plant on demolition contracts converted last year to quarry aggregate campaigns, adding a self-cleaning iron remover ahead of the secondary Impact Crusher. The plant carried a 250 kVA genset for the crusher and conveyors. The first configuration — an electromagnetic magnet with a 7 kW coil — repeatedly tripped during crusher direct-on-line starts, dropping captured steel onto the Conveyor Idlers & Rollers line and twice forcing same-day belt repairs. The operator's corrective package, supplied and commissioned with HUATAO Mining Screen, had three parts: replace the electromagnetic unit with a permanent-magnet block of matched reach (the feed was coarse demolition-derived steel, not fine buried iron), move the 1.5 kW belt motor onto a dedicated genset branch circuit with a soft starter, and re-aim the discharge chute using a trajectory chart verified at measured belt speed. Results over the following 1,800-hour campaign: zero magnet-related trips, belt motor current stable at 2.1 A, genset standby fuel reduced by roughly 1.6 L/h (about $4,500 of fuel saved over the season at delivered prices), and zero crusher damage events versus three steel-entry incidents in the prior electromagnetic period. The operator's conclusion matches the framework above: for a genset-equipped plant running coarse tramp iron, permanent magnet + electric belt is the lowest-risk, lowest-burn configuration; the electromagnetic option is reserved for deep-burden ore work where only a powered coil reaches.

FAQ

Q1: Can I power a self-cleaning electromagnetic iron remover from a hydraulic circuit?

No. The electromagnetic coil needs rectified DC at high amperage; hydraulics can drive only the cleaning belt. If the magnet is electromagnetic, a genset is mandatory.

Q2: How much extra fuel does a self-cleaning magnet really burn on a mobile plant?

A permanent-magnet unit with an electric belt adds roughly 0.2–0.4 L/h; an electromagnetic unit adds 1.5–2.0 L/h because the coil runs continuously; a hydraulic belt drive adds about 0.3–0.6 L/h through engine load.

Q3: Will a hydraulic-driven magnet belt slow down as the machine warms up?

Yes, by up to ±10% across oil-temperature extremes, depending on valve design. Since the discharge trajectory depends on belt speed, drift can push captured iron back onto the conveyor. A priority flow valve and a speed sensor substantially reduce this risk.

Contact Us

Contact: Annie Lu

Email: annie.lu@huataogroup.com

Phone / WhatsApp: +86 180 3242 2676

Website: http://www.tufflexscreen.com

We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.



Pub Time : 2026-11-20 16:48:23 >> News list
Contact Details
TOGETHER HTL LTD

Contact Person: Mr. Maple

Tel: +86 17778255675

Fax: 86--311-80690567

Send your inquiry directly to us (0 / 3000)