Rubber-covered rolls are important components in paper machines and paper converting equipment. Depending on their position, they may operate under continuous nip pressure, repeated deformation, process water exposure, chemical contact, and elevated temperatures.
Over time, these conditions can affect the cover surface and its mechanical properties. Three common forms of damage are cracking, delamination, and swelling.
Although these problems may occur together, they do not have the same failure mechanism. Cracking involves a fracture in the cover material. Delamination means that adhesion between bonded layers has been lost. Swelling refers to an increase in cover volume or dimensions, often accompanied by changes in hardness and surface appearance.
For maintenance engineers, identifying the actual cause is more important than simply removing the visible defect. If the original mechanical, chemical, or thermal problem remains, a newly ground or recoated roll may experience similar damage again.
Cracking may result from mechanical fatigue, impact, excessive temperature, chemical exposure, or unsuitable storage conditions.
Rubber-covered rolls are repeatedly compressed and released during operation. Excessive nip loading, uneven pressure distribution, unsuitable roll crown, or abnormal deflection can increase stress in particular areas.
Fatigue cracks that run relatively straight and parallel to the roll axis may indicate a crowning or loading problem. Their location should be compared with the roll profile and nip impression.
A roll may also experience additional stress if the bearing support, loading mechanism, or mating roll is not functioning correctly.
Paper wads, foreign objects, or accumulated material passing through a nip can create sudden impact damage.
Impact cracks are often irregular and concentrated in a localized area. Their appearance differs from the more regular orientation sometimes associated with fatigue cracking.
When this damage occurs, maintenance teams should review recent web breaks, felt failures, and material accumulation events.
Excessive surface temperature may accelerate cover deterioration. Chemical exposure can also change the mechanical properties of the cover compound and make it more vulnerable to cracking.
Cleaning products, oils, solvents, and process chemicals should be reviewed whenever a new crack pattern appears after a chemical or maintenance change.
A rubber cover can be damaged even before the roll is installed.
Ozone exposure, unsuitable storage near electrical motors, oil contamination, direct sunlight, cold impact, and improper lifting can all contribute to premature cover deterioration.
Rolls should be supported and handled through their journals rather than resting on the rubber surface.
Delamination occurs when the cover loses adhesion to the underlying layer or when the bonding between the base layer and the roll shell fails.
A covered roll may include a metal shell, a prepared bonding surface, bonding materials, a base layer, and an outer rubber compound. The complete system must maintain adhesion under the actual mechanical and environmental conditions.
Possible causes include:
Inadequate metal surface preparation.
Incorrect bonding materials.
Unsuitable curing conditions.
Water or process liquid entering the bonding interface.
Thermal gradients between the roll body and cover.
Chemical deterioration of the bonding system.
Excessive nip loading or mechanical impact.
Incorrect cover selection for the application.
For internally water-cooled rolls, the relationship between the temperature of the roll body and the surrounding process environment deserves attention.
A thermal gradient can encourage water movement through the cover. If water accumulates at the cover-to-shell interface, the bonding system may deteriorate and adhesion loss can develop.
The cooling arrangement, water exposure, cover construction, and operating temperature should therefore be reviewed together.
Maintenance teams should investigate localized blisters, raised areas, unusual temperature differences, changes in vibration, abnormal operating sound, and visible cover movement.
However, a visual inspection cannot always determine the full extent of internal adhesion loss.
If significant delamination is suspected, the roll should be removed from service for specialist assessment. Continuing to operate a seriously damaged cover may increase the affected area and create a reliability risk.
Swelling is commonly associated with chemical absorption or incompatibility between the cover compound and substances contacting it.
Different rubber and polyurethane formulations have different resistance to oils, solvents, water, and process chemicals. A cleaning agent suitable for one material may cause swelling or softening in another.
Potential sources include:
Cleaning solvents.
Petroleum-based products.
Oils and lubricants.
Papermaking chemicals.
Shower additives.
Maintenance chemicals.
Chemical residues from previous production conditions.
Depending on the material and exposure, swelling may cause increased diameter, reduced hardness, a tacky or oily surface, blistering, and changes in wear resistance.
Water absorption can also contribute in certain cover systems. Its effect depends on the formulation, temperature, exposure time, and construction of the cover.
First, compare the current cover condition with its original specification and maintenance records.
Measure hardness and diameter at multiple axial positions. Record whether swelling is uniform or localized. Review all substances that may contact the cover, including cleaning products and maintenance chemicals.
If the problem appeared after a change in the cleaning or process chemical program, compatibility testing or consultation with the cover supplier may be necessary.
Cover damage often results from several conditions acting together rather than from one isolated factor.
Important operating parameters include:
Nip pressure and pressure distribution.
Roll crown and deflection.
Machine speed and cyclic loading.
Cover hardness and material formulation.
Surface temperature.
Cooling efficiency.
Shower coverage and cleaning pressure.
Felt condition and contamination.
Foreign objects passing through the nip.
Uneven loading can increase local mechanical stress. Contamination may create abnormal contact conditions. Poor cooling or unsuitable cleaning can accelerate material deterioration.
The correct cover specification must therefore match the actual roll position, machine conditions, and chemical environment.
A structured inspection helps determine the type and severity of damage.
Visual inspection: Record crack direction, location, length, density, blistering, discoloration, surface roughness, and signs of separation.
Hardness testing: Measure hardness at several positions across the working face. Compare the results with the original specification and previous inspection data.
Diameter measurement: Measure the roll diameter at multiple axial positions. Check for increased dimensions, localized swelling, or an uneven profile.
Temperature monitoring: Compare the temperature distribution across the roll face and investigate abnormal hot spots or changes from the normal operating baseline.
Chemical review: List process chemicals, cleaning agents, oils, and solvents that may contact the roll. Confirm compatibility with the cover compound.
Bonding assessment: If delamination is suspected, arrange a specialist inspection to evaluate the bonding layers and roll shell.
Operating history: Review nip loading, machine speed, cooling conditions, web breaks, felt events, and maintenance records.
Combining these results provides a better basis for determining whether the damage is superficial or involves the internal structure.
The maintenance method should be selected according to the damage mechanism and the remaining condition of the roll.
Grinding may restore a surface when the cover remains bonded, the damage is limited, and sufficient cover thickness is available within the required diameter and profile limits.
Recoating may be appropriate when the cover has deteriorated beyond normal grinding limits or has sustained significant damage.
Bonding repair or complete recoating requires a technical assessment of the affected interface, cover construction, and roll body. The feasibility depends on the extent of adhesion loss.
Replacement should be evaluated when damage is extensive, structural integrity is uncertain, excessive deformation exists, or repair is uneconomical.
A swollen cover should not simply be reground before identifying the chemical cause. Similarly, grinding should not be used to conceal suspected internal delamination.
Preventive maintenance should combine correct material selection, operating control, chemical compatibility, and regular inspection.
Recommended practices include:
Select the cover material according to the roll position and actual process conditions.
Confirm chemical compatibility before introducing new cleaning agents or process chemicals.
Monitor surface temperature and investigate localized hot spots.
Check nip pressure distribution, roll crown, and alignment.
Maintain suitable cooling and shower conditions.
Prevent paper wads and foreign objects from passing through the nip.
Inspect the cover during planned shutdowns.
Record hardness, diameter, crown, and repair history.
Store rolls on their journals and protect the cover from impact, ozone, and chemical contamination.
A consistent inspection record helps maintenance teams identify gradual changes before they develop into serious damage.
Different paper-related applications require different roll structures, surface specifications, and maintenance practices.
For information about roll cover materials, read Paper Machine Roll Covers: Rubber, Polyurethane, Ceramic & Tungsten Carbide.
For paper machine geometry and roll calibration, see Why Does Forming Section Roll Matrix Calibration Standardize Sheet Uniformity in Modern Paper Machines?.
Corrugated board production uses a different roll system. How Does Custom Corrugating Roll Flute Design Maximize Board ECT While Cutting Paper Take-Up Costs? discusses flute design in corrugating applications. Corrugating rolls should not be confused with rubber-covered paper machine rolls.
HUATAO GROUP provides industrial roller supply solutions and technical coordination for paper, packaging, and related industries.
For replacement and customized roller projects, we can review customer drawings, dimensions, equipment specifications, cover requirements, and operating conditions to evaluate a suitable supply approach.
Visit HUATAO Rolls for company and product information. Learn more about the company through About HUATAO, explore Other Industrial Rolls, and find additional technical information in our News section.
Cracks, delamination, and swelling are different forms of rubber roll cover failure. Mechanical fatigue, impact, excessive heat, chemical incompatibility, water ingress, bonding problems, and unsuitable storage can all contribute.
A reliable diagnosis combines visual inspection, hardness and diameter measurements, temperature monitoring, chemical compatibility review, and bonding assessment.
Identifying the original cause before grinding, recoating, or replacing a roll helps reduce repeated damage and supports more reliable paper machine operation.
Related Products & Resources
Paper Machine Roll Covers
Paper Machine Rolls
Corrugating Rolls
Other Industrial Rolls
Contact Information
Tony Liu
General Manager | International Department
Mobile / WhatsApp / WeChat: +86 13383112591
Email: sale08@huataogroup.com
Website: https://www.huataorolls.com/
Contact Person: Mr. Maple
Tel: +86 17778255675
Fax: 86--311-80690567