Not necessarily, and usually not first. The exciter is the most expensive component in the drive chain and the least likely to be the root cause. A machine that will not vibrate may have a problem in its electrical supply, starter or control circuit, drive motor, belt or coupling, bearings, screen support, or the exciter itself. The correct first step is to identify exactly what the machine is doing, make the equipment safe, and follow a fault-finding sequence from the power source toward the vibration mechanism. Do not dismantle the exciter before simpler causes have been checked.
"No vibration" is not one symptom. A screen that will not start, a motor running without vibration, low amplitude and uneven vibration are four different problems.
The V-belt is the most common cause of motor-running-no-vibration. It is also the cheapest to check and fix.
Sequence runs from power outward. Supply, motor, transmission, exciter, support.
Do not dismantle the exciter to look for a fault. Internal work requires OEM procedures and qualified personnel.
Measurement replaces guessing. Amplitude, frequency and phase against commissioning baseline identifies uneven response.
Unapproved adjustments cause damage. Eccentric weights, speed, drive configuration and VFD parameters should not be changed without approval.
| Symptom | Most Likely Cause | First Check |
|---|---|---|
| Screen does not start | No power; tripped starter; interlock; locked mechanism | Supply, protection devices, motor condition |
| Motor runs, screen does not vibrate | Slack or broken V-belt; damaged coupling | Belt tension, coupling condition |
| Amplitude too low | Belt slip; changed weights; material overload; blocked deck | Belt, weight settings, feed rate |
| Uneven or abnormal vibration | Loose mounting; damaged spring; bearing; rotation mismatch | Mounts, springs, bearing condition, motor rotation |
| Abnormal noise from drive | Bearing damage; misalignment; loose fastener | Bearing, alignment, fastener torque |
Vibrating screen no-vibration fault means the screen is not producing the expected working motion. It may be a complete stoppage, a motor running without screen motion, low amplitude, or abnormal vibration pattern.
Exciter is the vibration-generating component — either a mechanical eccentric mechanism driven by an external motor, or an integrated vibration motor with eccentric weights on the shaft.
Troubleshooting sequence in this context means the ordered path from power supply through motor, transmission, vibration mechanism and screen support, checking each stage before moving to the next.
A vibrating screen depends on a coordinated system, and failure can occur at any point in the chain.
The drive chain. Motor supplies power. Drive arrangement transmits it — V-belts, coupling, cardan shaft or direct coupling. Exciter or vibration motor converts rotation into oscillating force. Screen body, springs and structure respond to that force.
Why the sequence matters. A failure at any point produces a symptom that looks similar from the operator's position. The motor may run, the screen may not move, and the assumption is a failed exciter. In practice, a slack V-belt produces exactly that symptom on a belt-driven screen and costs a fraction of an exciter replacement to fix.
Why dismantling is the wrong first step. Exciter internal inspection requires OEM procedures, correct tools, specified clearances and qualified personnel. Dismantling an exciter that is functioning correctly introduces risk of assembly error and does not address the actual fault. Manufacturer guidance explicitly recommends checking obvious causes before disassembly.
Why measurement matters. Amplitude, frequency, orbit and phase at fixed measurement points identify where the response has changed. A difference between drive side and opposite side points to a support or synchronization problem. A difference between feed and discharge ends points to load distribution. Measurement converts a vague symptom into a specific diagnostic clue.
Correct diagnosis first time, avoiding replacement of serviceable components.
Lower repair cost because the cheapest and most common causes are checked before the most expensive.
Reduced downtime when the fault is simple and identified quickly.
Safer maintenance because dismantling and heavy component replacement are minimised.
Better spare parts planning when failure modes are recorded and analysed.
Longer component life when root causes are corrected rather than symptoms masked.
Large mining screens in iron ore, copper ore, gold ore and base metal circuits.
Aggregate processing screens operating continuously under abrasive duty.
Coal preparation where wet screening and variable feed apply.
Belt-driven screens where V-belt condition is a frequent cause of no-vibration faults.
Direct-coupled and vibration motor installations where motor and coupling inspection are primary.
Dual-motor linear screens where rotation and synchronization are critical.
These duties sit between size reduction in CRUSHING and downstream CLASSIFICATION or DEWATERING. A screen that stops vibrating halts the circuit, not just the deck.
| Property | Complete Stoppage | Motor Running, No Vibration | Low Amplitude | Uneven Vibration |
|---|---|---|---|---|
| Most likely cause | Power, starter, interlock, lock | V-belt, coupling | Belt slip, weights, overload | Mounting, spring, bearing, rotation |
| Safety step | Isolate and lock out | Isolate and lock out | Isolate for inspection | Isolate for inspection |
| Personnel required | Qualified electrician | Maintenance technician | Maintenance technician | Maintenance technician plus measurement |
| Typical cost | Low to moderate | Low | Low to moderate | Moderate to high |
| Risk if misdiagnosed | Replacing exciter unnecessarily | Replacing exciter unnecessarily | Adjusting weights without approval | Structural damage if ignored |
| Scenario | Dominant Symptom | Diagnostic Priority |
|---|---|---|
| Screen stopped suddenly after power trip | Complete stoppage | Supply, starter, protection state |
| Motor hums but does not start | Complete stoppage with hum | Supply voltage, phase, mechanical resistance, bearing |
| Motor running, screen stationary | Motor running, no vibration | Belt tension and condition, coupling, shaft connection |
| Screen vibrates weakly during production | Low amplitude | Feed rate, bed depth, deck blockage, belt slip |
| Screen vibrates weakly on empty test | Low amplitude | Drive, weights, bearing, spring condition |
| Screen vibrates with abnormal pattern | Uneven vibration | Mounting, springs, rotation, synchronization, structural contact |
| Industry | Typical Drive | Common No-Vibration Cause | Diagnostic Priority |
|---|---|---|---|
| Iron ore | Belt-driven large frame | V-belt slip or breakage | Belt condition and tension |
| Copper | Belt or direct-coupled | Coupling failure; bearing seizure | Coupling and bearing inspection |
| Gold | Multi-motor linear | Rotation or synchronization mismatch | Rotation direction, motor wiring |
| Coal | Belt-driven sealed units | Contamination ingress; belt slip | Sealing, belt condition |
| Aggregates |
Pub Time : 2026-11-19 09:19:57
>> News list
Contact Details
TOGETHER HTL LTD
Contact Person: Mr. Maple Tel: +86 17778255675 Fax: 86--311-80690567 |